Guides ·

How to set up artwork for large format print

Document size, scale, bleed, safe areas, fonts, colour mode and export settings: what to get right before you send large format artwork to print.

How to set up artwork for large format print

Artwork that looks perfect on screen can still cause trouble at large format. Text ends up hidden in a hem, a logo turns out blurry at three metres wide, or a colour shifts because the file was built for a website. None of this is difficult to avoid if you set the file up correctly from the start. This guide walks through the decisions in the order you will meet them.

Start with the finished size

Before you open your design software, confirm the exact finished size of the print, in millimetres, and whether it is landscape or portrait. For a banner, that is the size after hemming. For a board, it is the trimmed size of the panel. For a stand graphic, it is the size the hardware calls for, which is not always the same as the visible area.

If you are printing for a stand you already own, tell us the make and width so we can confirm the graphic size. If you are unsure of anything, ask before you build the file. Resizing finished artwork to a different shape almost always means reworking the layout.

Working at scale

Very large documents can be awkward to handle, and some programs have a maximum page size. The usual answer is to work at a fixed scale, such as 1:10 or 1:4, and tell us the scale when you send the file. A 5000mm banner built at 1:10 becomes a 500mm document. If you do this, remember that image resolution has to scale up too: a photo placed in a 1:10 file needs ten times the resolution you would need at full size. Our guide to resolution for large format prints explains how much you need.

Bleed: extend the background past the edge

Bleed is extra image that runs beyond the finished edge, so there is no thin white line if the trim is a fraction out. Any colour, photo or pattern that touches the edge should continue into the bleed area. How much bleed a job needs depends on the product. A trimmed board needs a little; a banner that is hemmed, a canvas that wraps around a frame or a graphic that wraps a panel edge may need considerably more. Check the bleed for your job with us before you start rather than guessing.

Safe area: keep the important things inside

The safe area is the zone inside the finished edge where text, logos, phone numbers and faces should sit. Close to the edge, content can be lost in a hem, punched through by an eyelet, hidden by a frame or a pole pocket, or rolled into the base of a roller banner. As a rule, the more finishing a product has, the bigger the margin you should leave. Treat the safe area as a hard limit for anything someone needs to read.

Colour: build in CMYK

Screens make colour from red, green and blue light (RGB). Printers lay down cyan, magenta, yellow and black inks (CMYK). Some bright RGB colours, especially vivid greens, blues and oranges, have no exact CMYK equivalent, so they look duller in print. Building the file in CMYK from the start shows you a more realistic preview and avoids surprises at conversion. If your brand uses Pantone references, include them in your notes. There is more on this in matching brand colours in print.

For large areas of solid black, ask us whether a richer black build is suitable for your material, because plain 100% black can look slightly grey over a large surface.

Text, fonts and lines

  • Outline your fonts, or embed them fully in the PDF, so nothing is substituted.
  • Think about reading distance. Text that is comfortable on a screen at arm’s length may be unreadable on a banner seen from across a street. Bold, simple typefaces travel further.
  • Avoid hairline rules and very fine type reversed out of a dark or busy background.
  • Spell-check, and check phone numbers and web addresses twice. A typo at two metres wide is hard to miss.

Images and logos

Use vector artwork for logos, text and line graphics wherever you can. Vectors stay sharp at any size. Photographs are made of pixels, so they need enough resolution at the finished size and viewing distance. Do not rely on enlarging a small web image; the software can add pixels but it cannot add detail. If your only copy of a photo is a print, slide or negative, it can be scanned first.

Exporting the file

A high-quality PDF is usually the safest format: fonts embedded or outlined, images at full resolution, bleed included, crop marks optional. Flatten transparencies only if your software handles it reliably. Send one file per design, name each file with its size and version, and include a low-resolution preview if the job has several parts. Then send it through our artwork upload page with a note of the size, material and quantity.

Checking before you send

Our artwork proof checker is a quick way to spot obvious problems. We also check files ourselves before printing. If something is wrong, such as missing bleed or low-resolution images, we will tell you rather than print it. If you would rather not set the file up yourself, our in-house designers can create, adapt or resize artwork for large format.

Ready to send?

When your file is ready, upload your artwork with the finished size, material and quantity, or request a quote first if you are still deciding on materials. If anything in this guide does not fit your job, ask before you build the file; a two-minute question at the start saves a rebuild later.

Questions

What file format should I send for large format print?

A high-quality PDF with fonts embedded or outlined, images at full resolution and bleed included is usually the safest choice. If you only have another format, send it and we will tell you whether it is usable.

How much bleed do I need?

It depends on the product. A trimmed board needs a small amount; hemmed banners, wrapped canvases and some stand graphics need more. Ask us for the bleed and safe area for your job before you start.

Can I send artwork in RGB?

We can work from RGB files, but colours will shift when converted to print. Building in CMYK lets you see a more realistic version of your colours before anything is printed.

Can you fix my artwork if it is not set up correctly?

Yes. We check files before printing and our in-house designers can adapt, resize or rebuild artwork for large format. Tell us what you have and what you need.

Request a quote · Send artwork · 0203 026 0636

Tell us what you need printed

Give us the size, the material and the date you need it. We will check your files and send a quote.

0203 026 0636
London80 Willow Walk, Unit 1, London SE1 5SY
0203 026 0636   sales@superchrome.com